Keithparris: Add bit numbers for Bits 12 and 13

2022-12-20T15:26:27Z

Add bit numbers for Bits 12 and 13

← Older revision		Revision as of 15:26, 20 December 2022
Line 43:		Line 43:
	\| If set, disables the logging of error log entries by LAN drivers.		\| If set, disables the logging of error log entries by LAN drivers.
	\|-		\|-
	\| 0		\| 12
	\| If set, enables a fast timeout on transmit requests, usually between 1 and 1.2 seconds instead of 3 to 4 seconds, for most LAN drivers.		\| If set, enables a fast timeout on transmit requests, usually between 1 and 1.2 seconds instead of 3 to 4 seconds, for most LAN drivers.
	\|-		\|-
	\| 0		\| 13
	\| If set, transmits that are given to the LAN device and never completed by the device (transmit timeout condition) are completed with error status (SS$_ABORT) rather than success status (SS$_NORMAL).		\| If set, transmits that are given to the LAN device and never completed by the device (transmit timeout condition) are completed with error status (SS$_ABORT) rather than success status (SS$_NORMAL).
	\|}		\|}

	[[Category:System Parameters]]		[[Category:System Parameters]]

Darya.zelenina: Created page with "'''LAN_FLAGS''' is a dynamic bitmask system parameter used to enable features in the local area networks port drivers and support code. The default value..."

2019-04-09T09:20:27Z

Created page with "'''LAN_FLAGS''' is a dynamic bitmask system parameter used to enable features in the local area networks port drivers and support code. The default value..."

New page

'''LAN_FLAGS''' is a dynamic bitmask [[System Parameters|system parameter]] used to enable features in the local area networks port drivers and support code. The default value for LAN_FLAGS is 0.

=Bit Definitions=

{| class="wikitable"
! colspan="col" | Bit
! colspan="col" | Description
|-
| 0
| The default of zero indicates that ATM devices run in SONET mode. If set to 1, this bit indicates ATM devices run in SDH mode.
|-
| 1
| If set, this bit enables a subset of the ATM trace and debug messages in the LAN port drivers and support code.
|-
| 2
| If set, this bit enables all ATM trace and debug messages in the LAN port drivers and support code.
|-
| 3
| If set, this bit runs UNI 3.0 over all ATM adapters. (Auto-sensing of the ATM UNI version is enabled if both bit 3 and bit 4 are off (0).)
|-
| 4
| If set, this bit runs UNI 3.1 over all ATM adapters. (Auto-sensing of the ATM UNI version is enabled if both bit 3 and bit 4 are off (0).)
|-
| 5
| If set, disables auto-negotiation over all Gigabit Ethernet Adapters.
|-
| 6
| If set, enables the use of jumbo frames over all Gigabit Ethernet Adapters.
|-
| 7
| Reserved
|-
| 8
| If set, disables the use of flow control over all LAN adapters that support flow control.
|-
| 9
| Reserved
|-
| 10
| Reserved
|-
| 11
| If set, disables the logging of error log entries by LAN drivers.
|-
| 0
| If set, enables a fast timeout on transmit requests, usually between 1 and 1.2 seconds instead of 3 to 4 seconds, for most LAN drivers.
|-
| 0
| If set, transmits that are given to the LAN device and never completed by the device (transmit timeout condition) are completed with error status (SS$_ABORT) rather than success status (SS$_NORMAL).
|}

[[Category:System Parameters]]

LAN FLAGS - Revision history

Keithparris: Add bit numbers for Bits 12 and 13

Darya.zelenina: Created page with "'''LAN_FLAGS''' is a dynamic bitmask system parameter used to enable features in the local area networks port drivers and support code. The default value..."