Junji: update about set device/served

2021-11-25T05:28:54Z

update about set device/served

← Older revision		Revision as of 05:28, 25 November 2021
Line 1:		Line 1:
	'''SET DEVICE''' is a [[DCL]] [[Command\|command]] that establishes a [[Printer\|print device]] or [[Terminal\|terminal]] as a [[Spooling\|spooled]] device or establishes the operational status for a device. To make a disk on a local node available to all the nodes on an OpenVMS [[Cluster]], use ~~the~~ /SERVED ~~qualifier~~. Requires [[OPER]] ~~(operator)~~ privilege. [[PHY_IO]] (physical I/O) privilege is required when specifying the Alpha-only qualifiers that change the characteristics of shadow sets. These qualifiers also can be specified using the [[SET SHADOW]] command, which provides additional options for controlling [[Shadow Set\|shadow sets]]. Qualifier settings for shadow sets remain in effect until they are changed using either [[SET DEVICE]] or [[SET SHADOW]] or until the shadow set or shadow set member is dismounted. If the shadow set is remounted or a shadow set member is returned to the shadow set from which it was dismounted, the settings must be specified again.		'''SET DEVICE''' is a [[DCL]] [[Command\|command]] that establishes a [[Printer\|print device]] or [[Terminal\|terminal]] as a [[Spooling\|spooled]] device or establishes the operational status for a device.

			To make a disk on a local node available to all the nodes on an OpenVMS [[Cluster]], use [[SET DEVICE/SERVED]].

			'''Requires [[OPER]] privilege.'''

			[[PHY_IO]] (physical I/O) privilege is required when specifying the Alpha-only qualifiers that change the characteristics of shadow sets. These qualifiers also can be specified using the [[SET SHADOW]] command, which provides additional options for controlling [[Shadow Set\|shadow sets]]. Qualifier settings for shadow sets remain in effect until they are changed using either [[SET DEVICE]] or [[SET SHADOW]] or until the shadow set or shadow set member is dismounted. If the shadow set is remounted or a shadow set member is returned to the shadow set from which it was dismounted, the settings must be specified again.
	=Syntax=		=Syntax=
	SET DEVICE [device-name[:]]		SET DEVICE [device-name[:]]
Line 19:		Line 25:
	* /PREFERRED_CPUS		* /PREFERRED_CPUS
	* /READ_COST		* /READ_COST
	* /RESET/SITE		* /RESET
			* /SITE
	* /SPOOLED		* /SPOOLED
	* /SWITCH		* /SWITCH
	* /SERVED
	[[Category:DCL Commands]]		[[Category:DCL Commands]]

Jane.doe: Created page with "'''SET DEVICE''' is a DCL command that establishes a print device or terminal as a spooled device or establishes the oper..."

2019-12-03T12:08:58Z

Created page with "'''SET DEVICE''' is a DCL command that establishes a print device or terminal as a spooled device or establishes the oper..."

New page

'''SET DEVICE''' is a [[DCL]] [[Command|command]] that establishes a [[Printer|print device]] or [[Terminal|terminal]] as a [[Spooling|spooled]] device or establishes the operational status for a device. To make a disk on a local node available to all the nodes on an OpenVMS [[Cluster]], use the /SERVED qualifier. Requires [[OPER]] (operator) privilege. [[PHY_IO]] (physical I/O) privilege is required when specifying the Alpha-only qualifiers that change the characteristics of shadow sets. These qualifiers also can be specified using the [[SET SHADOW]] command, which provides additional options for controlling [[Shadow Set|shadow sets]]. Qualifier settings for shadow sets remain in effect until they are changed using either [[SET DEVICE]] or [[SET SHADOW]] or until the shadow set or shadow set member is dismounted. If the shadow set is remounted or a shadow set member is returned to the shadow set from which it was dismounted, the settings must be specified again.
=Syntax=
SET DEVICE [device-name[:]]
==Qualifiers==
* /ABORT_VIRTUAL_UNIT
* /AVAILABLE
* /COPY_SOURCE
* /DUAL_PORT
* /ENABLE
* /ERROR_LOGGING
* /FORCE_REMOVAL
* /LOG
* /MEMBER_TIMEOUT
* /MV_INTVL
* /MV_NUM
* /MVTIMEOUT
* /PATH
* /POLL
* /PREFERRED_CPUS
* /READ_COST
* /RESET/SITE
* /SPOOLED
* /SWITCH
* /SERVED
[[Category:DCL Commands]]

SET DEVICE - Revision history

Junji: update about set device/served

Jane.doe: Created page with "'''SET DEVICE''' is a DCL command that establishes a print device or terminal as a spooled device or establishes the oper..."