Search results
- ... broken, an error message is displayed and the command procedure may fail. 1. Every line in a command procedure that is not a data line has to begin ...2 KB (264 words) - 12:59, 23 March 2022
- This category contains articles describing OpenVMS startup command procedures. Use Template:Startup Command Procedures in your article to make a ...6 members (0 subcategories, 0 files) - 19:04, 24 June 2022
- REDIRECT Command procedure31 bytes (3 words) - 13:00, 23 March 2022
- ... procedure command procedure executes at command level 1, and a command procedure called by the interactive command procedure executes at command ...840 bytes (124 words) - 13:50, 12 January 2019
- ... /freeware/v10/msend/ 10 , 20, 30, 40, 80 - SET_CLOCK The command procedure diddles a couple of registers in VMS, causing the system clock to run ...228 KB (33,783 words) - 18:52, 12 July 2023
- ... as SHOW DEFAULT output. - DEPTH Integer Current command procedure depth. The command procedure depth is 0 when you log in interactively and ...6 KB (852 words) - 10:53, 11 November 2019
- ... verification off. When image verification is on, data lines in the command procedure are displayed on the output device. =Examples= $ SAVE_PROC_VERIFY ...3 KB (403 words) - 12:40, 31 March 2020
- ... You may add commands to this procedure or change the commands within this $ procedure as needed for your system. This command procedure is preserved ...17 KB (2,405 words) - 05:06, 14 February 2019
- ... www.digiater.nl/openvms/decus/vax92b/rcsmake/ DECUS tapes - '''rcswild''' VAX92B Command procedures to allow VMS RCS to be used on wildcarded ...246 KB (38,872 words) - 20:02, 20 November 2019
- ... at a terminal or include them in Command_procedure command procedures . These command procedures can be run interactively or submitted to ...73 KB (10,966 words) - 01:24, 5 June 2022
- ... be: $ PIPE SHOW SYSTEM @TEE showsys.log SEARCH SYS$INPUT LEF The command procedure TEE.COM is used to log the data flowing through the pipeline. ...10 KB (1,419 words) - 17:02, 2 December 2019
- ... Specifies either the input device or the file for the preceding command, or the command procedure to be executed. The default file type is .COM. The ...4 KB (677 words) - 11:15, 22 December 2022
- ... to store and manipulate data in command procedures and on the command line to pass data between command procedures in a single process =Data types ...8 KB (1,397 words) - 09:43, 22 December 2022
- ... and tend to fill up the directory over time. To activate the command procedure, you will need to first comment out the preceding $ EXIT command. ...50 KB (7,396 words) - 17:34, 26 January 2022
- ... run interactively, the default value of SYS$INPUT is the command procedure file. In a command procedure run as a Batch Job batch job , the default ...3 KB (433 words) - 18:46, 24 June 2022
- ... EXIT) is reinstated. =Examples= $ ON SEVERE_ERROR THEN CONTINUE A command procedure that contains this statement continues to execute normally when ...2 KB (243 words) - 10:39, 2 December 2019
- ... job. The first command submits the command procedure IMPORTANT.COM. In the second command, the SYNCHRONIZE command tells the procedure to wait for ...4 KB (583 words) - 19:28, 28 June 2019
- ... If you place DEFINE SYS$OUTPUT filespec as the first line in a command procedure, output will be directed to the file you specify. Category:DCL ...3 KB (479 words) - 12:27, 2 December 2019
- ... ://www.digiater.nl/openvms/freeware/v30/mx041/ V4.2 ) - MakeShare Creates a command procedure to link a shared imaged from an object library ...28 KB (4,116 words) - 11:35, 19 October 2021
- ... CONTINUE In this example, the command procedure statement requests the command interpreter to continue executing the procedure if any warning, error ...1 KB (173 words) - 14:04, 2 December 2019