... enables the autostart feature on a node for all autostart Queue ... command to automatically start on the node all active autostart queues that are ...
817 bytes (125 words) - 15:20, 2 December 2019
... down security auditing on the system, use the following commands on each node in the cluster: $ SET AUDIT/ALARM/AUDIT/DISABLE=ALL/CLASS= $ SET AUDIT ...
2 KB (378 words) - 09:56, 23 August 2023
... automatic start-up of Tomcat. For example: $ openssl req -x509 -sha256 -nodes -days 365 -newkey rsa:4096 -keyout - _$ /tomcat$root/sslkeys/server.key ...
49 KB (7,079 words) - 07:13, 20 October 2021
... clustered environments . It lets you define your management environment as a node, group of nodes, or an entire cluster, and execute commands on all ...
2 KB (252 words) - 18:06, 5 April 2019
... number of votes that a computer contributes towards the quorum. For Satellite Node satellite nodes , the value is 0; for all other computers, the ...
4 KB (589 words) - 15:39, 17 August 2021
... CHANNEL cluster to crash with bugcheck code MC_FORCED_CRASH if this node bugchecks or shuts down. The default value is 0. A setting of 1 is intended ...
522 bytes (84 words) - 09:47, 9 April 2019
... Cluster. In an OpenVMS Cluster, if caching is disabled on any node, none of the other nodes can use the extended file cache or the virtual I/O cache. ...
1 KB (204 words) - 09:29, 2 July 2019
... status block will not be filled in) until all branches on the local node have been removed from the transaction. Thus this call to $ABORT_TRANS cannot ...
12 KB (1,841 words) - 15:11, 15 July 2019
... circuit (VC) that carries messages between the local node (where you are running SDA) and another remote node, enter the SDA command SHOW PORT/VC ...
1 KB (210 words) - 13:38, 8 November 2019
... circuit (VC) that carries messages between the local node (where you are running SDA) and another remote node, enter the SDA command SHOW PORT/VC ...
1 KB (210 words) - 13:58, 8 November 2019
... _MANAGER") SMAN43$ show sym a A = "MYQUEUE_MANAGER" - MANAGER_NODES String The names of the nodes on which the queue manager may run. SMAN43$ ...
4 KB (640 words) - 13:25, 26 November 2019
... access paths to the devices change. Prior to OpenVMS Version 7.2 , all nodes with direct access to the same multipathed device were required to use ...
1 KB (199 words) - 18:25, 13 December 2019
... that the LANpath between two nodes, including the local and remote ... size. In other words, only nodes with large-packet LAN adaptersconnected ...
3 KB (398 words) - 11:57, 9 April 2019
... , this parameter applies to all virtual circuits between the node on which it is set and other nodes in the cluster. NISCS_PORT_SERV has the DYNAMIC ...
1 KB (188 words) - 13:01, 8 November 2019
... invalid class, all classes are enabled. In a clustered environment, this file is node specific. Messages that get into the log file can be controlled ...
2 KB (404 words) - 18:44, 4 June 2019
... mode, the writes issued by each remote node are, by default, sent one by one ... If the writes sent by a remote node reach an upper threshhold of ...
2 KB (261 words) - 16:18, 2 July 2019
... mode, the writes issued by each remote node are, by default, sent one by one ... If the writes sent by a remote node reach an upper threshhold of messages ...
1 KB (198 words) - 16:19, 2 July 2019
... can be used to reduce the time to transfer data between two OpenVMS nodes when the LAN speed between them is limiting the data transfer rate, and ...
3 KB (470 words) - 17:24, 26 July 2021
... in an Cluster OpenVMS Cluster . It is assigned to the node when the node enters a cluster. An example of a CSID is '10010'. To display CSID of all ...
591 bytes (98 words) - 08:05, 2 December 2019
... rejects records for DECnet for OpenVMS requests made by the specified nodes - /BEFORE Selects all records time-stamped before the specified time ...
3 KB (491 words) - 13:11, 6 February 2023
