... or restarts the specified network service on the localnode. The /NETWORK qualifier is required. =Syntax= START/NETWORK network-service Category:DCL ...
222 bytes (30 words) - 17:43, 2 December 2019
... ''' is a DCL Command command that registers the attributes of a network service. Requires SYSNAM (system name) privilege. =Syntax= SET ...
402 bytes (45 words) - 12:59, 3 December 2019
... command that displays information about network services registered on a node. =Syntax= SHOW NETWORK network-service Qualifiers /FULL /OLD ...
230 bytes (28 words) - 10:54, 3 December 2019
... ; they are not included with the Integrity servers). You can use InfoServer network booting to boot from a virtual DVD drive on the network. You can ...
73 KB (10,966 words) - 01:24, 5 June 2022
... Files are encoded to be resistant to the corruption that many mailers and networks generate. When all parts of the share file are combined and run as ...
228 KB (33,783 words) - 18:52, 12 July 2023
... that either is not part of the cluster or is unknown to the network ACP. Check the node name specification. Use the DCL command SHOW CLUSTER to ...
122 KB (18,338 words) - 07:03, 23 December 2019
... LM SCSI tape LMA0: - LP Printer LPA0: - LT LAT Network Terminal - MB Mailbox MBA0: - MF TU78 Magnetic Tape - MG ...
6 KB (846 words) - 11:51, 3 February 2020
... $ THEN $ $ Following are the commands that start up the DECnet Phase IV network, if you $ are using the DECnet Phase IV software. Note that only ...
17 KB (2,405 words) - 05:06, 14 February 2019
... - DEFAULT_USERNAME Specifies the default local user name for incoming network proxy - DEVICE_NAME Specifies the name of a device in audit ...
14 KB (2,109 words) - 02:26, 26 November 2021
... by the following keywords: ALL BATCH DETACHED DIALUP LOCAL NETWORK REMOTE SERVER SUBPROCESS See the LOGFAILURE keyword for further ...
8 KB (1,069 words) - 15:37, 11 December 2019
... Utility This is a utility to transfering VMS's files over the TCP/IP network to a remote non-VMS hosts, a like the FTP or SFTP but with additional ...
28 KB (4,116 words) - 11:35, 19 October 2021
... monitor one or more OpenVMS nodes on an extended LAN or wide area network (WAN). That is, the nodes for which you are collecting the information must ...
13 KB (1,893 words) - 08:30, 17 July 2019
... book provides an introduction to SAN and Ethernet networking, and how these networks help to achieve a smarter data center. The publication describes ...
25 KB (3,483 words) - 09:59, 29 August 2022
... Default: DCL (does not usually need to be changed). Ignored for network processes. /CLITABLES specifies user-defined CLI tables for the account. The ...
8 KB (1,100 words) - 14:43, 3 December 2019
... 5/366 PICMG SBC - Alpha 5/433 PICMG SBC DE500-BA Network Adapter DE500-FA Network Adapter (run-time only) - HAILSTORM 2 V7.1-2 March 03,1992 ...
27 KB (3,690 words) - 19:58, 4 March 2023
... interactive login limit SET LOGIN/INTERACTIVE - Modify network login limit SET LOGIN/NETWORK - Modify batch login limit SET LOGIN/BATCH ...
6 KB (963 words) - 11:28, 2 December 2019
... _ACCESS_S Sets, as a 3-byte value, the range of times during which network access is permitted for secondary days. Each bit set represents a 1-hour ...
24 KB (4,006 words) - 09:56, 8 June 2019
... JPI$_RMS_DFNBC Returns the default block count for local buffers for network access to remote files. - JPI$_RMS_EXTEND_SIZE Returns the default ...
49 KB (8,143 words) - 07:47, 14 November 2019
... ": the system begins to monitor the terminal, terminal server connection, or network connection where the login is taking place (whether failures from ...
2 KB (338 words) - 13:26, 18 January 2019
... the same as an interactive login. A proxy login means that specific network access operations can be executed, such as a copy operation. By contrast ...
2 KB (361 words) - 07:10, 28 February 2019
